Seams
Seams are primed, taped and rolled with lap sealant at the edges.
Flat Roofing
Rubber Roof Installation Park Ridge, NJ
A Park Ridge roofer who installs EPDM can put a new rubber roof on a flat or low slope section of almost any home, with as few seams as possible. Call (551) 390-0358 to reach a local roofer.
Rubber roofing usually means EPDM, though some people use the term for any single-ply membrane. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. Unlike TPO and PVC, its seams are taped rather than heat welded.
Attachment method shapes the rest of the installation. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. On most homes, fully adhered EPDM is the usual choice because it handles wind well and stays smooth.
Two more decisions round out the plan. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. Black is standard and holds heat, while white reflects it. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
Depending on what the roofer finds, rubber roof installation in Park Ridge, NJ can go hand in hand with rubber roof repair and flat roof installation.
Need rubber roof installation in Park Ridge? Call (551) 390-0358 to reach a nearby roofing contractor.
Call nowThe process
How rubber roof installation works
Each layer is set up to give the membrane a smooth, solid base.
Prepare the deck
The deck is repaired and checked for slope, ideally a quarter inch per foot toward drains or gutters. A tear-off comes first on existing roofs.
Add the cover board
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Slope can be built in at this stage.
Lay the sheet
The membrane is unrolled, aligned and allowed to settle before bonding. Seam layout follows the direction of drainage.
Bond the membrane
Contact adhesive goes on the board and the membrane, and once it is tacky, the sheet is laid down and brushed. Each half gets the same treatment in turn. Air pockets left under the sheet can turn into blisters later, so the crew works the rubber flat from the center out.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Exposed edges get lap sealant.
Flashing
Walls and curbs get membrane flashing held by termination bar, pipes get pre-molded boots and corners get uncured flashing. Termination bar and counter flashing seal the wall edge. Before the crew leaves, seams are probed for any loose spots.
What is included
Parts of a new EPDM roof
Cover board
Rigid insulation and a cover board form the base and gives the adhesive a firm grip.
Deck preparation
The base is cleared and checked so the roof sits on solid wood.
Edge metal
Termination bar, pipe boots and edge metal are installed for a finished roof.
Rubber sheet
The rubber membrane is adhered or fastened over a clean, dry base.
Related service
EPDM Roof Installation Park Ridge, NJ
Installing EPDM well comes down to preparation, seams and flashing. The membrane has to lie flat on a clean, dry cover board, the adhesive has to reach the right tack before the sheet is laid and every seam has to be primed and rolled with care. Dry, mild days give the best bond. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
For a Park Ridge home, the installer thinks ahead to how the roof will behave over the years. Perimeter securement and proper flashing help prevent the shrinkage problems older rubber roofs show. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Park Ridge are common on porches, garages, additions and flat sections of older homes. Across Park Ridge and nearby towns like Woodcliff Lake, Montvale, Hillsdale and Saddle River, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
Need rubber roof installation around Park Ridge? Call (551) 390-0358 for a Park Ridge roofer who serves the towns around it too.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Park Ridge, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Drier ceilings
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Park Ridge and nearby towns.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Installation FAQ
How long does a new rubber roof last?
Rubber roofs often last decades. Good seams, drainage and occasional checks make the difference. Patching EPDM is straightforward.
Which EPDM thickness should I choose?
EPDM usually comes in 45 or 60 mil for homes. Sixty mil resists punctures better and lasts longer, which helps on roofs with foot traffic or hail. Thicker 90 mil membrane exists for heavy use.
What is the difference between EPDM and TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. Black EPDM is taped and stretchy, and white TPO is welded and reflective. Both are common on flat roofs.
What color EPDM is best?
Color affects heat gain. Black EPDM absorbs heat, which can help in cold climates, while white EPDM reflects sunlight and keeps the rooms below cooler. Talk through the choice with a roofer.
Is it possible to install EPDM over the old roof?
Recovering depends on the condition of the old roof. The old roof must be a single dry layer, with a recover board over it. Otherwise, a tear-off is needed. The roofer tests the old roof for moisture before recommending a recover.
More questions? Call (551) 390-0358
Often needed together
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, never with tar or asphalt cement that ruins the rubber.
Learn moreFlat Roof Installation
New flat roofs built with real slope, insulation, a cover board and a membrane suited to the building, with every wall, curb and penetration flashed properly.
Learn moreTPO Roofing
White, heat-welded TPO single-ply roofing for low-slope homes and buildings, sized to the deck, the drains and the way the roof is used.
Learn moreFlat Roof Replacement
Full replacement of failing flat roofs, with a moisture survey deciding tear-off or recover, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof installation help in Park Ridge
Call now for Park Ridge rubber roof installation and help in the towns around it.